Servis Sağlayıcı Lisansı almak isteyen birçok firma ve arkadaşın en büyük problemlerinden biri de BTK’ nın lisans işlemlerinden önce bazı isterleri olmasıdır.
Bunlardan biri de altyapı kurulumudur. Bu makalede size Juniper SSG20 serisi firewall için örnek bir konfigurasyon paylaşmak istedim.
Eminim ki bu örnek konfigurasyona internet üzerinde ulaşamayabilirsiniz. Umarım yararlı bir paylaşım olur.
Unutmayalım, Bilgi paylaştıkça çoğalır …
unset key protection enable
set clock timezone 0
set vrouter trust-vr sharable
set vrouter “untrust-vr”
exit
set vrouter “trust-vr”
unset auto-route-export
exit
set alg appleichat enable
unset alg appleichat re-assembly enable
set alg sctp enable
set auth-server “Local” id 0
set auth-server “Local” server-name “Local”
set auth default auth server “Local”
set auth radius accounting port 1646
set admin name “netscreen” (netscreen YERİNE YENİ BİR USER TANIMLAYIN)
set admin password “” (YENİ BİR ŞİFRE TANIMLAYIN)
set admin auth web timeout 10
set admin auth dial-in timeout 3
set admin auth server “Local”
set admin format dos
set zone “Trust” vrouter “trust-vr”
set zone “Untrust” vrouter “trust-vr”
set zone “DMZ” vrouter “trust-vr”
set zone “VLAN” vrouter “trust-vr”
set zone “Untrust-Tun” vrouter “trust-vr”
set zone “Trust” tcp-rst
set zone “Untrust” block
unset zone “Untrust” tcp-rst
set zone “MGT” block
unset zone “V1-Trust” tcp-rst
unset zone “V1-Untrust” tcp-rst
set zone “DMZ” tcp-rst
unset zone “V1-DMZ” tcp-rst
unset zone “VLAN” tcp-rst
unset zone “Untrust” screen tear-drop
unset zone “Untrust” screen syn-flood
unset zone “Untrust” screen ping-death
unset zone “Untrust” screen ip-filter-src
unset zone “Untrust” screen land
set zone “V1-Untrust” screen tear-drop
set zone “V1-Untrust” screen syn-flood
set zone “V1-Untrust” screen ping-death
set zone “V1-Untrust” screen ip-filter-src
set zone “V1-Untrust” screen land
set interface adsl1/0 phy operating-mode auto
set interface “ethernet0/0” zone “Untrust”
set interface “ethernet0/1” zone “Null”
set interface “wireless0/0” zone “Trust”
set interface “bgroup0” zone “Trust”
set interface “adsl1/0” pvc 8 35 mux llc protocol bridged qos ubr zone “Untrust”
set interface bgroup0 port ethernet0/1
set interface bgroup0 port ethernet0/2
set interface bgroup0 port ethernet0/3
set interface bgroup0 port ethernet0/4
unset interface vlan1 ip
set interface ethernet0/0 ip (BTK NIN VERDİĞİ IP ADRESINI GİRİN ! XXX.XXX.XXX.XXX/27)
set interface ethernet0/0 route
set interface bgroup0 ip (BTK NIN VERDİĞİ IP ADRESINI GİRİN ! XXX.XXX.XXX.XXX/29)
set interface bgroup0 nat
set interface ethernet0/0 gateway (BTK NIN VERDİĞİ GATEWAYİ GİRİN ! XXX.XXX.XXX.XXX)
unset interface vlan1 bypass-others-ipsec
unset interface vlan1 bypass-non-ip
set interface ethernet0/0 ip manageable
set interface bgroup0 ip manageable
set interface ethernet0/0 manage ping
set interface ethernet0/0 manage ssh
set interface ethernet0/0 manage telnet
set interface ethernet0/0 manage snmp
set interface ethernet0/0 manage web
set interface bgroup0 manage mtrace
set interface ethernet0/0 vip interface-ip
set interface bgroup0 dhcp server service
set interface bgroup0 dhcp server auto
unset interface bgroup0 dhcp server config next-server-ip
set interface “serial0/0” modem settings “USR” init “AT&F”
set interface “serial0/0” modem settings “USR” active
set interface “serial0/0” modem speed 115200
set interface “serial0/0” modem retry 3
set interface “serial0/0” modem interval 10
set interface “serial0/0” modem idle-time 10
set flow tcp-mss
unset flow tcp-syn-check
unset flow tcp-syn-bit-check
set flow reverse-route clear-text prefer
set flow reverse-route tunnel always
set pki authority default scep mode “auto”
set pki x509 default cert-path partial
set crypto-policy
exit
set ike respond-bad-spi 1
set ike ikev2 ike-sa-soft-lifetime 60
unset ike ikeid-enumeration
unset ike dos-protection
unset ipsec access-session enable
set ipsec access-session maximum 5000
set ipsec access-session upper-threshold 0
set ipsec access-session lower-threshold 0
set ipsec access-session dead-p2-sa-timeout 0
unset ipsec access-session log-error
unset ipsec access-session info-exch-connected
unset ipsec access-session use-error-log
set url protocol websense
exit
set policy id 1 from “Trust” to “Untrust” “Any” “Any” “ANY” permit
set policy id 1
exit
set nsmgmt bulkcli reboot-timeout 60
set ssh version v2
set ssh enable
set config lock timeout 5
unset license-key auto-update
set telnet client enable
set wlan country-code AT
set wlan 0 channel auto
set wlan 1 channel auto
set wlan change-channel-timer 0
set snmp port listen 161
set snmp port trap 162
set snmpv3 local-engine id “0164092008000839”
set vrouter “untrust-vr”
exit
set vrouter “trust-vr”
unset add-default-route
exit
set vrouter “untrust-vr”
exit
set vrouter “trust-vr”
exit
